other crochet materials Archives

Shining (ribbon) stars

Our Christmas tree has no topper. We’d love to get a high-end crystal star for it, but that’s yet in the future. Meanwhile I’ve been improvising – one year we had wide ribbon tied in bows, one year I made an origami star out of construction paper (because it was the only appropriately-colored paper I had that was large enough). This year I decided to crochet a star out of ribbon, and got the chance to this weekend. The result is shown below, blurrily, on the tree, after my loving husband arranged the lights behind it for best effect.

I thought at first that I would chain stitch ribbon around wire, bend it into shape, and connect the ends; nesting two or three of different sizes would fill out the star. That might have worked if my wire had been a bit heavier, but as it was it was too flimsy, and it was also difficult to smooth and flatten the wire without crimping and creasing the ribbon.

Then I went looking for patterns and found one by Kimura Kraft that I liked the look of. Unfortunately it didn’t work in ribbon; the inner part was somehow too large for the outside.

Fortunately I had purchased three “kegs” of ribbon, so after two strikes I could still try for a hit, modifying that pattern. For the star shown I used a J hook (6mm), a 40ft roll of 3/16 inch wide ribbon (12.2m|~5mm), and a generous 2ft (60cm) of 28-gauge jewelry wire. I had a decent bit of ribbon left, but only about half the difference to the next available size down, 32ft (9.75m).

Here are my changes to Markus’s pattern. Unfamiliar abbreviations below (and the rest of them too) are explained on the Crochet Reference page.
Round 1: Replace the starting ring and chains with “ch-4, work into ch next to sl kn.” Make sure to put your sl kn onto the hk loosely – ribbon is inelastic.
Round 2: Ch 3 to start instead of 2; work only 1 dc where it says to work 2 (so don’t make that first dc, in particular).
Round 3: This one’s different enough that it’s simpler to give the instructions in full. Note that “in picot” means to treat the “sl st in 3rd ch from hk” parts of rnd 2 as chain rings, working into the center:
No ch this rnd. Work the following stitches around the wire as well as the rnd-2 sts, leaving a wire tail of several inches: *sc 2 around next ch-2; [sc 2, ch 1, dc, ch 1, sc 2] in picot; sc 2 around next ch-2; sk dc* around. Sl st into 1st sc of rnd to join (40 sc, 10 ch, 5 dc). FO ribbon.
Twist ends of wire together and use to attach star to tree or other hanging/display place. Shape by hand.

Wire crochet experiments

As promised, I crocheted with wire for the first time last night. The evening began with me teaching my Crochet Via Granny Squares class, so my first idea was a little wire granny square.

It didn’t go so well. I started with green floral wire, probably about 28 gauge, maybe 26, which was stiff with its coating. Second round was 30 gauge gold wire. Both were with a size 1 steel hook (2.75mm). My tension was all over the place – with the gold wire especially, it was impossible to get a grip on it without bending it and risking kinks. Not that I didn’t get kinks regardless. After the fact it occurred to me that finger cots on two or three fingers of my left hand might be a help, but by then I was getting ready for bed.

I did feel like I was starting to get the hang of it, as uneven as that second round is, but by then I was kind of over the whole granny square idea and decided to make a chained chain. I used the same hook, and red wire that was unlabeled, but probably 28-30 gauge. That went better, especially because the unevenness of my loops is not as apparent as the uneven height of the double crochet stitches.

Speaking of kinks, as we were a while ago, I tried to reel the wire straight off the spool instead of letting it come off the end, coiled, because I read a hint somewhere that I’d get fewer kinks that way. I didn’t have much luck getting the gold wire to unreel like that, but the red wire was better behaved. I think it did result in fewer kinks, but not their complete elimination.

I thought about trying beaded wire crochet, but it was getting late and I didn’t have any ideas that appealed to me much. Instead, in honor of how birds-nest-y my wire crochet is (especially the granny), I made a wrapped wire bird’s nest.

Frigid rain all day yesterday. I do like winter, but not that aspect. 🙂

Crochet with ribbon

I finished my work early one night recently and, taken by surprise by that event, looked around for something to fill a little time before bed. I decided to try crocheting with ribbon, pulled from my stash. I used PlanetJune’s Love Hearts pattern.

The white and gold heart was made with 1/8″ wire-edged ribbon and an E hook. The dark blue heart was made with a J hook and non-wired ribbon that had loops along the edge; without the loops it was a bit over 3/16″ wide, and with the loops it was 3/8″. They both turned out fairly sturdy and I think crocheted ribbon baskets and catch-alls would work quite well. The one difficulty with ribbon, that slows down the stitching, is that it wants to coil up into a nice corkscrew as you go along. I could probably have alleviated that by detaching it from the spool, but even once I did with the blue ribbon it still coiled until the free end was short enough to no longer drag on the floor. Instead I had to smooth it every stitch or three. It still didn’t take too long to make these hearts.